WEEK 29 (FYP SEM 2)    12th NOVEMBER 2012

TITLE: FYP Poster Presentation

OBJECTIVE: Completing the FYP Poster for FYP Presentation

CONTENT/PROCEDURE:

Finally, the day of FYP Presentation has come. The Poster has been completed according to the format given during briefing. For my poster, the content include:

• Abstract
• Objective
• Methodology (include Block diagram and Flow Chart)
• Result
• Reference

 RESULT/ANALYSIS:

Here is the poster designed for FYP presentation.

CONCLUSION:

Alhamdulilah, FYP has ended. Now, I have to complete the report and submit it before the due come. Lots of thanks I bid to ALLAH S.W.T for making my way smooth, and also lots of thanks to my supervisor, Sir Abdul Rashid bin Othman, other lecturers, Dr Khairil, Sir Tan, Mdm Zurin, En Zaba and all my friends for their guidance and support. I hope I will score an A for my FYP subject, amin.  

 " ...With ALLAH blessing, plus with Supervisor guidance, plus with Family support, plus with Friends advise, I know I will do my best to finish this project, INSYAALLAH..."

WEEK 28 (FYP SEM 2)      12th NOVEMBER 2012

TITLE: Overall view of Project


OBJECTIVE: Completing FYP project of Auto Feeder For Pets

CONTENT/ PROCEDURE:

Alhamdulilah, finally my FYP project had been complete and functioning well. All the equipment is connected to each other and the test of result for each component has been carried out. The solar charger is functioning, solar panel produce reading, timer circuit is functioning and also the mechanical part, motor and blade also functioning well.

TOP VIEW OF OVERALL PROJECT

RESULT/ ANALYSIS:

Here are the result for each component that being tested :

For Solar Panel performance, the graph regarding the solar panel position Vs the voltage and also the solar panel position against the current had been plotted. As we can see, the highest reading is at 1000p.m horizontal position and the lowest reading is at vertical position at 0900a.m.

GRAPH OF SOLAR PANEL PERFORMANCE ( SOLAR PANEL POSITION VS VOLTAGE)

GRAPH OF SOLAR PANEL PERFORMANCE ( SOLAR PANEL POSITION VS CURRENT)

For solar charger, it functioning well when it charge the battery and the output produce is 12V.

SOLAR CHARGER FUNCTIONING, GREEN LED INDICATE PV IS CHARGING

OUTPUT FROM SOLAR CHARGER MEASURE 12V

For Timer Circuit, it provide user to set alarm up to eight different time label AL0 to AL7

CIRCUIT TIMER CONNECTION

CIRCUIT TIMER FUNCTIONING PROVIDE USER WITH EIGHT ALARM LABEL AL0 TO AL7

For motor and blade, it functioning well as the food is being dropped smoothly

MOTOR AND BLADE FUNCTIONING WELL, FOOD IS DROP. DC WATER PUMP PRODUCE FOUNTAIN

Here is the full video on how the project functioning:

CONCLUSION:

Alhamdulilah, finally its all end and the project running perfectly.


" ...With ALLAH blessing, plus with Supervisor guidance, plus with Family support, plus with Friends advise, I know I will do my best to finish this project, INSYAALLAH..."

WEEK 27 (FYP SEM 2)       3 NOVEMBER 2012

TITLE: Designing Portable Feeder : Attach Mechanical Part

OBJECTIVE: To install the food container and blade for food dropping process

CONTENT/PROCEDURE:

As this Feeder is upgrade to Portable Feeder, the main component has been change to. The mechanical part is change to make it fit within the bag. For this portable feeder, the bag use is a metal bag in form of briefcase. At first, I would like to use plastic trolly bag to ensure safety precaution against electrical wiring as plastic is known as insulator. But then, I have problem to install the mechanical part as the plastic bag having lots of problem in term of welding the metal to attach the component and also its too light to attach solar panel onto the case of the bag. Thus, I end up use metal homemade bag as to reduce the budget. 

RESULT/ ANALYSIS:

As a result of changing the form of this feeder, I need to accept the fact that the food container that used before which is plastic food container does not fit well with the bag. Thus, in order to make it easy to attach the container to the pipe of blade, as well as to make sure it fit the bag which means the bag can be close properly, the food container has been change into mini torchlight case. It just a temporary and of course it only a prototype and not final product yet. Thus, this project can be upgrade more in the future to make it more convenient. The timer circuit, solar charger, pump and solar panel are attach together in this bag.

Mini Torchlight represent food container and being attach to the pipe in the bag

close up of "food container" attach to pipe with motor

CONCLUSION:

As conclusion, this auto feeder is just a prototype and can be upgrade in future. 

" ...With ALLAH blessing, plus with Supervisor guidance, plus with Family support, plus with Friends advise, I know I will do my best to finish this project, INSYAALLAH..."

WEEK 26 (FYP SEM2) 29 OCTOBER 2012

TITLE: Designing portable feeder : Installing solar panel with the bag

OBJECTIVE: To create new design of feeder which is in portable bag : Issue on
                          installing  the Solar Panel

CONTENT/PROCEDURE:

This Auto Feeder has been upgrade into new design which is in Portable bag. All the equipment involve will be install in the portable bag including the solar panel. The feeder has been upgrade into Portable bag to make it more easier to use by the pet owner who wish to bring their pets together during the vacation as well as to make it easier to be locate in any places in the house if the they did not want to bring their pets together during the vacation.  This design enable the user to locate the feeder indoor or outdoor.

ANALYSIS/ RESULT:

The solar panel is attach on top of the outside bag. The solar panel is attach via stand which can be folded in any form of degree position. When the feeder is operating, the solar panel that attach behind the feeder can be fold in 15 degree position. For indoor use, the solar panel can be removed and install outside the house.

solar panel attach on top of the bag

Solar panel has stand that can fold in any position

CONCLUSION

This design serve to add the function of the feeder as portable feeder.


" ...With ALLAH blessing, plus with Supervisor guidance, plus with Family support, plus with Friends advise, I know I will do my best to finish this project, INSYAALLAH..."

WEEK 25 (FYP SEM 2)   29 OCTOBER 2012

TITLE: Testing Timer circuit

OBJECTIVE: To construct and Test Timer circuit for feeder

CONTENT/PROCEDURE:

 The timer Circuit has been constructed based on the diagram below. The component use as shown are PIC 16F84, buzzer, relay, transistor C547, voltage regulator, (10Kohm, 1Kohm,220 Ohm) resistors, capacitors, diodes, switch, 7-segment, 74HCT164 and LEDs.

schematic diagram of Timer

schematic diagram of timer

ANALYSIS/ RESULT:

This timer is design with alarm setting. The timer will display the current clock in hour and minutes and the alarm can be set to eight different time. For additional, this timer also can display days from Sunday to Saturday. This timer circuit has four main button which is T for time adjustment, A for alarm adjustment, + for incremental digit and - for decremental digit. The switch on/off will enable or disable the alarm.

For the circuit operation, the time is adjust to current time using the T button and + and - button. To set an alarm, the A button is pressed and the alarm can be set using + and - button and press T button to end process of setting an alarm. 

Clock display in hour and minutes

Alarm 0 until Alarm 7

Setting day Sunday to Saturday

For this feeder, the alarm is set for eight different time starting from 8:00 a.m, 11:00 a.m, 02:00 p.m, 05:00 p.m, 08:00 p.m, 11:00 p.m, 02:00 a.m, and 05:00a.m. 

Alarm time set

CONCLUSION

The timer circuit is functioning and consider as success.


" ...With ALLAH blessing, plus with Supervisor guidance, plus with Family support, plus with Friends advise, I know I will do my best to finish this project, INSYAALLAH..."

WEEK 24 ( FYP SEM 2)     28 OCTOBER 2012

TITLE: Battery as back up supply and Water pump for pets

OBJECTIVE: To give the feeder backup supply and adding water pump to feeder

CONTENT/ PROCEDURE:

For the backup supply, this feeder use Rechargeable battery GP Power. This Sealed Lead Acid Battery serve 12V with 7.2AH. The time for battery to run the load simply known by dividing the Amp Hour of the battery with the Amp Hour of load use.

Rechargeable Battery

 As for the water pump, the water pump use now is AC water pump. For now, this water pump remain as additional features as it required other sources as the main source of this feeder use DC supply. To be use in DC, an inverter circuit is needed to supply to the water pump using DC supply. For now, the water pump just remain as additional feature and may be upgrade in future with the use of inverter.

AC water pump

ANALYSIS/ RESULT:

The battery serve as backup perfectly. The water pump is submersible pump and when running create little fountain which in turn could attract the pets to use the feeder. The video shows how the pump is working.

 CONCLUSION:

The  part of the Feeder like water pump, blade and motor, battery and supply is running smoothly for now.


" ...With ALLAH blessing, plus with Supervisor guidance, plus with Family support, plus with Friends advise, I know I will do my best to finish this project, INSYAALLAH..."

WEEK 23 (FYP SEM 2)          28 OCTOBER 2012  

TITLE: Designing new blade for Auto Feeder

OBJECTIVE: To create the new blade to overcome the weaknesses of exist blade

CONTENT/ PROCEDURE:

The exist blade before result in many weaknesses and difficulty. When the motor is running, the blade did not run smoothly and having difficulty to push and drop the foods. The first blade which made up from perspex is not efficient as it is easily broken into pieces. The one with pipe design blade is not run smoothly and the metal blade also facing the same problem. 

broken perspex blade

ANALYSIS/RESULT:

So, as to overcome the problem, the blade has been design in auger shape and being attach into the pipe. For this trial, the first auger blade is create using perspex but in the end it turn out to be like before, easily broken and not so smooth.

perspex auger blade

 Thus, the auger blade is design using metal so that the quality is better and can last longer. When the motor is being attach to the metal auger blade, the food dropping process running smoothly.

metal auger blade

metal auger blade inserted in pipe

CONCLUSION:

The dropping process now running smoothly and consider a success.

" ...With ALLAH blessing, plus with Supervisor guidance, plus with Family support, plus with Friends advise, I know I will do my best to finish this project, INSYAALLAH..."